Solex ADDHE Carburetor Parts
Solex ADDHE Carburetor Parts

Solex ADDHE Parts

On this page you will find all currently available parts for the Solex ADDHE range carburetors.

Click HERE for an exploded view drawing of the Solex ADDHE.

The numbers in the drawing correspond to the numbers in brackets at the beginning of the article description.

We are still very much expanding our parts offerings for these carburettors so please contact us by email if the part that you are looking for is not yet listed.

Our Contact Page can be found HERE.

Solex ADDHE Carburetor Parts

!
SOLEXADDHETHROTTLESHAFT
(3) Throttle Shaft for Solex ADDHE Carburetors

(3) Throttle Shaft for Solex ADDHE Carburetors

Throttle shaft, made of special hardened steel, to fit the Solex ADDHE series carburetors.

This shaft fits the 40 mm, 45 mm and the 48 mm varieties of the ADDHE.

Comes complete with 4 new butterfly valve screws.

Required quantity per carburettor: 1

This is item number 3 in the drawing.

(3) Throttle Shaft for Solex ADDHE Carburetors

SOLEXBUTTER
(4) Butterfly Valve Screw for Solex ADDHE Carburetors

(4) Butterfly Valve Screw for Solex ADDHE Carburetors

Special screw to secure the butterfly valves in the Solex ADDHE series carburetors.

This concerns the version that is 9,5 mm long and has 4 millimeter standard metric thread with a conical head.

As Solex is notoriously bad documented, these screws probably fit a myriad of other (Solex) carburettors but we have no cross reference lists.

If you order these screws, please make sure that they are the correct version and size for your purpose.

Required quantity per carburettor: 4

This is item number 4 in the drawing of the ADDHE.

(4) Butterfly Valve Screw for Solex ADDHE Carburetors

ADDHEREGELEARLY
(15) Idle Mixture Screw for Solex ADDHE Carburetors - Early Type

(15) Idle Mixture Screw for Solex ADDHE Carburetors - Early Type

Screw to adjust the idle mixture on the early Solex ADDHE series carburetors.

This is the version which measures some 22 millimeter in total length and is being supplied including a new o-ring.

Please compare yours with the one in the photo to make sure it is the same version.

Required quantity per carburetor: 2

This is item number 15 in the drawing.

(15) Idle Mixture Screw for Solex ADDHE Carburetors - Early Type

ADDHEMSFINE
(15) Idle Mixture Screw for Solex ADDHE Carburetors - Fine Thread

(15) Idle Mixture Screw for Solex ADDHE Carburetors - Fine Thread

Screw to adjust the idle mixture on the Solex ADDHE series carburetors.

This is the version with the fine thread.
Please compare yours with the one in the photo to make sure it is the same version.

Required quantity per carburetor: 2

This is item number 15 in the drawing.

 

(15) Idle Mixture Screw for Solex ADDHE Carburetors - Fine Thread

ADDHEMSCOARSE
(15) Idle Mixture Screw for Solex ADDHE Carburetors - Coarse Thread

(15) Idle Mixture Screw for Solex ADDHE Carburetors - Coarse Thread

Screw to adjust the idle mixture on the Solex ADDHE series carburetors.

This is the version with the coarse thread.
Please compare yours with the one in the photo to make sure it is the same version.

Required quantity per carburetor: 2

This is item number 15 in the drawing.

 

(15) Idle Mixture Screw for Solex ADDHE Carburetors - Coarse Thread

10751PI
(371) Pump Diaphragm for Solex ADDHE carburetors

(371) Pump Diaphragm for Solex ADDHE carburetors

This is the diaphragm for the pump in the Solex ADDHE series carburetors.

Required quantity per carburetor: 1

This is item number 371 in the drawing.

 

 

(371) Pump Diaphragm for Solex ADDHE carburetors

ADDHEABP
Air By-Pass Screw for Solex ADDHE carburetors

Air By-Pass Screw for Solex ADDHE carburetors

Air By-Pass Screw for the Solex ADDHE series carburetors.

Please note that not every ADDHE is equipped with these by-pass screws.

Required quantity per carburetor (when applicable): 2

This item is NOT in the drawing.

 

Air By-Pass Screw for Solex ADDHE carburetors

ADDHE
Service Kit for 2 x Solex 40 ADDHE carburetors

Service Kit for 2 x Solex 40 ADDHE carburetors

Service kit for the Solex ADDHE 40 carburetor.

Contains the parts to service 2 carburettors.

Consists of the following parts:

  • Various gaskets
  • 2 Pump Diaphragms
  • 2 Needle Valves
  • 4 carburetor-to-inlet-manifold gaskets
  • Various rubber o-rings
  • Various aluminum washers

This is a Carburetor City carburettor service set, Made in Italy to the highest standards.

Service Kit for 2 Solex 40 ADDHE carburetors

FR2591
Rebuild Kit for 2 Solex 45 ADDHE carburetors for BMW Neue Klasse and 2002

Rebuild Kit for 2 x Solex 45 ADDHE carburetors for BMW Neue Klasse and 2002

Service kit for the quite rare Solex ADDHE 45 milimeter carburetors.

These carburetors can be found, amongst others, on the following cars:

  • BMW 1800 TISA (Neue Klasse)
  • BMW 2000 TI (Neue Klasse)
  • BMW 2002 TI

Although these carburetors were originally delivered on the above cars, they are often transplanted onto other cars and engines so the range of vehicles that these service kits might fit is much broader.
Alternatively, your car might no longer be equipped with the carburetor that it left the factory with.

So, please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.

Contains the parts to service 2 carburettors.

Consists of the following parts:

  • All required gaskets
  • 2 Pump Diaphragms
  • 2 Needle Valves size 160
  • 4 Inlet Plenum Gaskets
  • All required rubber o-rings and copper, aluminum and fiber washers

This is a Carburetor City service kit of superior Italian manufacture.

Rebuild Kit for 2 Solex 45 ADDHE carburetors for BMW Neue Klasse and 2002

FR2591
Rebuild Kit for 2 Solex 45 ADDHE carburetors for Volvo B-Series

Rebuild Kit for 2 x Solex 45 ADDHE carburetors for Volvo B-Series

Service kit for the quite rare Solex ADDHE 45 milimeter carburetors.

These carburetors can be found, amongst others, on the following cars:

  • Volvo B18
  • Volvo B20
  • Volvo B23 Sport
  • Volvo B30

Although these carburetors were originally delivered on the above cars, they are often transplanted onto other cars and engines so the range of vehicles that these service kits might fit is much broader.
Alternatively, your car might no longer be equipped with the carburetor that it left the factory with.

So, please compare your old parts carefully with the ones in the picture as there are many different versions of this carburetor.

Contains the parts to service 2 carburettors.

Consists of the following parts:

  • All required gaskets
  • 2 Pump Diaphragms
  • 2 Needle Valves size 160
  • 4 Inlet Plenum Gaskets
  • All required rubber o-rings and copper, aluminum and fiber washers

This is a Carburetor City service kit of superior Italian manufacture.

Rebuild Kit for 2 Solex 45 ADDHE carburetors for Volvo B-Series

PUMPTOOLSOLEX
Solex ADDHE Pump Tool

Solex ADDHE Pump Tool

ONLY A FEW SETS IN STOCK!

This is an absolutely ingenious tool for anybody working the side draught Solex ADDHE's!

With this set, you can measure exactly how much fuel the pump jet pump is delivering through the jets and adjust it where desired.

Gone are the days with your carbs in a vice and trying to catch and measure the fuel... this set can be used IN SITU on the car!

Set of 4 of these tools, enough for 2 sidedraught Solex ADDHE's.

Attention !
These are New-Old-Stock sets dating from the 1970's.

Solex ADDHE Pump Tool

cosx4
Cosworth Carburettor Mounts - carburetor to manifold

Cosworth Carburettor Mounts - carburetor to manifold

Developed by British-based racing engineers Cosworth, these buffers are specifically designed to be used in conjunction with Misab-plates.

Nowadays produced by that same Misab company from Sweden, the mounts are strong enough to ensure an airtight seal while also providing enough vibration damping.

Each mount consists of two cups and one rubber buffer.

Install the Misab-plates, install your carb(s), install the Cosworth mounts using a Nyloc nut (NOT included in the standard set!) and set the distance between the cups to 2 millimeter, using a normal feeler gauge.
The buffer is now set to the correct tension to dampen vibrations but not allowing air leaks.

These mounts are supplied in sets of 4 complete mounts (as depicted) which is enough for one carburettor like a Dellorto DHLA, Solex ADDHE, Weber DCOM or Weber DCOE.

Note:
Following many requests from our customers, we have sourced superior quality stainless steel locking nuts in size M8 which is the most common size used on carburetor studs.

For your convenience, you can select these from the drop box and order them right along with the buffers but please verify that your studs have that same, M8, thread.

Cosworth Carburettor Mounts - carburetor to manifold

misabx2
Original Misab Plates carburetor mounts

Original Misab Plates carburetor mounts

Developed by MIS AB in Sweden, these mounts are specifically designed to be used in conjunction with the Cosworth buffer mounts.

These plates ensure ensure an airtight seal between carburettor and manifold, thanks to their vulcanized rubber ring.

For the best result, we strongly advise the combination with the Cosworth buffer mounts.

Install the Misab-plates, install your carb(s), install the Cosworth mounts using a Nyloc nut (NOT included in the standard set!) and set the distance between the cups to 2 millimeter, using a normal feeler gauge.
The buffer is now set to the correct tension to dampen vibrations but not allowing air leaks.

These MISAB plates are supplied in sets of 2 which is enough for one carburettor like a Dellorto DHLA, Solex ADDHE, Weber DCOM or Weber DCOE.

For your convenience you can order the Cosworth buffer mounts and high quality Stainless Steel Self-Locking M8 nuts right along with it.

Original Misab Plates carburetor mounts

51730.080
4 x Stainless Steel Self-Locking Nuts in size M8

4 x Stainless Steel Self-Locking Nuts in size M8

Following many requests from our customers, we have sourced superior quality stainless steel locking nuts in size M8 which is the most common size used on carburetor studs.

These are commonly used to secure double-barrel, horizontal, carburetors like Dellorto DHLA, Weber DCOE and Solex ADDHE to the studs in their manifolds.

Please verify that your studs have that same, M8, thread.

We sell these nuts in sets of 4.

4 x Stainless Steel Self-Locking Nuts in size M8

40/15
15 mm long bolt-on trumpet for 40mm carburetors

15 mm long bolt-on trumpet for 40mm carburetors

Top quality machined alloy bolt-on trumpet for 40mm diameter carburetors.

These trumpets measure 15 mm in total length.

Diameter at the flared end is some 57mm.

They will fit the following carburetors:

  • Dellorto DHLA40
  • Dellorto DRLA40
  • Weber DCOE40
  • Weber IDF40
  • Solex, SK and DCOW carburetors with a 40mm bore
  • Throttle bodies with 65mm stud centers and 40mm bore

15 mm long bolt-on trumpet for 40mm carburetors

40/25
25 mm long bolt-on trumpet for 40mm carburetors

25 mm long bolt-on trumpet for 40mm carburetors

Top quality machined alloy bolt-on trumpet for 40mm diameter carburetors.

These trumpets measure 25 mm in total length.

Diameter at the flared end is some 57mm.

They will fit the following carburetors:

  • Dellorto DHLA40
  • Dellorto DRLA40
  • Weber DCOE40
  • Weber IDF40
  • Solex, SK and DCOW carburetors with a 40mm bore
  • Throttle bodies with 65mm stud centers and 40mm bore

25 mm long bolt-on trumpet for 40mm carburetors

8257
43 mm long bolt-on trumpet for 40mm carburetors

43 mm long bolt-on trumpet for 40mm carburetors

Top quality machined alloy bolt-on trumpet for 40mm diameter carburetors.

These trumpets measure 43mm in total length.

Diameter at the flared end is some 57mm.

They will fit the following carburetors:

  • Dellorto DHLA40
  • Dellorto DRLA40
  • Weber DCOE40
  • Weber IDF40
  • Solex, SK and DCOW carburetors with a 40mm bore
  • Throttle bodies with 65mm stud centers and 40mm bore

43 mm long bolt-on trumpet for 40mm carburetors

E40/60G
62 mm long bolt-on trumpet with gauze for 40 mm carburetors

62 mm long bolt-on trumpet with gauze for 40 mm carburetors

Newly arrived 62 mm long bolt-on trumpet with gauze for 40 mm carburetors

Top quality machined alloy bolt-on trumpet with coarse gauze, for 40 mm diameter carburetors.

Machined from a solid billet of aluminum.

This trumpet is of the so-called bolt-on type and thus requires two nuts & bolts to be attached to the carburettor.

These trumpets measure 62 mm in length to which some 13 mm has to be added for the domed gauze filter, making a total length of 75 mm.

Diameter at the flared end is some 64 mm.

They will fit the following carburetors:

  • Dellorto DHLA40
  • Dellorto DRLA40
  • Weber DCOE40
  • Weber IDF40
  • Solex ADDHE
  • Solex, SK and DCOW carburetors with a 40 mm bore
  • Throttle bodies with 65 mm stud centers and 40 mm bore

62 mm long bolt-on trumpet with gauze for 40 mm carburetors

PX300ADDHE
Pipercross PX300 Airfilter System for Solex ADDHE Carburetors

Pipercross PX300 Airfilter System for Solex ADDHE Carburetors

This is the Pipercross PX300 air filter system for 1 Solex ADDHE carburateur.

An explanation of this ingenious system can be found HERE.

A set consists of a baseplate made to fit the Solex ADDHE series and, when desired, a PX300 filter element of your choice.

To make life a little easier for you you can open the tables with sizes in a new window by clicking HERE.

To allow you engine to breath as freely as possible, we advise you to take the largest filter that you can fit under the bonnet.

If you are using ram pipes or trumpets, then please allow at least 19 mm of space between the trumpet mouth and inner face of the filter.

The desired shape and size of the filer can be selected through the dropbox at the top of this page.

Should you desire just the filter element, then please click HERE.

Pricing of these sets is as follows:

 Base plate ONLY  US$ 24.95
 Filterelement ONLY  US$ 64.95
 Total  US$ 89.90


When purchasing a baseplate and element together, we can offer these at US$ 84.95 giving you a savings of US$ 4.95 per set.

Pipercross PX300 Airfilter System for Solex ADDHE Carburetors

PX300FILTER
Pipercross PX300 Airfilter Element

Pipercross PX300 Airfilter Element

These are the Pipercross PX300 air filter elements, to be used in combination with the PX300 baseplates.

An explanation of this ingenious system can be found HERE.

The filters are produced from triple-laminated Pipercross filter foam and are supported on the inside by sturdy mesh.

The filters are produced in two basic shapes, the “Dome” and the“Box”.
The differences between the two are best demonstrated in the photos below:

De tegenhanger van de "Bolhoed", de "Doos" vindt u HIER maar de verschillend worden het duidelijkst in onderstaande foto: The filters are produced in two basic shapes, the “Dome” and the“Box”.

The filters always have the same "groundplan" of 190 x 190 mm in order to fit onto the base plates.

The differences are in the shape and in- and external height.

To allow you engine to breath as freely as possible, we advise you to take the highest filter that you can fit under the bonnet.

If you are using rampipes or trumpets, then please allow at least 19 mm of space between the trumpet mouth and inner face of the filter.

The following heights are available for the various models:

Pipercross PX300 Dome Filter
 Dome   External Height   Internal Height 
 C302D 

 65 mm

 40 mm

 C303D 

 90 mm

 65 mm

 C304D 

 125 mm

 100 mm

 

Pipercross PX300 Box Filter
 Box   External Height   Internal Height 
 C3001 

 40 mm

 25 mm

 C3002 

 55 mm

 40 mm

 C3003 

 80 mm

 65 mm

 C3004 

 115 mm

 100 mm


You can choose the required shape and size through the dropbox at the top of this page.

To make life a little easier for you you can open the tables with sizes in a new window by clicking HERE.

Attention!
This is the filter element only.
To be able to use this, you will always require a PX300 base plate, suitable for your carburetor.
The various baseplates that we have available can be found in the PiperCross PX300 department.

Pipercross PX300 Airfilter Element

C1050
C1050 Pipercross Universal Airfilter Socks for Ram Pipes

C1050 Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

These socks are easily tailored to size by shortening them with a pair of scissors.

The generous inner diameter makes them suitable for virtually all rampipes.

Created out of the famous Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

This is the "normal" version, very well suited for street and track use. Should you be using your vehicle in extremely dusty circumstances, like auto- and motocross, we recommend the Heavy Duty version, C1050MX.

Dimensions:

  • Internal diameter: 70 mm
  • External diameter: 95 mm
  • Internal height: 100 mm
  • External height: 115 mm

Before putting the socks in place, you cut them to size. Then slide them onto the ram pipes and, when desired, you can secure them in place with a simple plastic tie-strap.

Although Pipercross supplies these only in pairs, we understand the need in the market for "singles" and consequently we sell these individually.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1050 Pipercross Universal Airfilter Socks for Ram Pipes

C1050MX
C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous Heavy Duty Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

These socks are easily tailored to size by shortening them with a pair of scissors.

The generous inner diameter makes them suitable for virtually all rampipes.

Created out of not less than 3 layers of the famous, green, Heavy Duty Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

Being the heavy duty version, these socks are very well suited for use in extremely dusty circumstances like auto- and motocross.

For street and track use, the better option is to pick the normal version, C1050.

Dimensions:

  • Internal diameter: 55 mm
  • External diameter: 95 mm
  • Internal height: 95 mm
  • External height: 120 mm

Before putting the socks in place, you cut them to size. Then slide them onto the ram pipes and, when desired, you can secure them in place with a simple plastic tie-strap.

Although Pipercross supplies these only in pairs, we understand the need in the market for "singles" and consequently we sell these individually.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1050MX Heavy Duty Pipercross Universal Airfilter Socks for Ram Pipes

C1052
C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

These are the famous "enclosed" Pipercross Ram Pipe Socks which are probably the most universal airfilter solution when working with individual air stacks.

Contrary to the C1050 "open" socks, this version has a rear panel with opening so that it "hugs" the ram pipe.

The generous inner diameter makes them suitable for virtually all rampipes.

The opening in the rear panel measures some 55 mm in diameter but can of course be stretched significantly thanks to the nature of the foam.

Created out of 3 layers of the the famous Pipercross foam, the socks don't require any oiling but are used "dry" and are easily washed out in water with a mild detergent.

Dimensions:

  • Internal diameter: 80 mm
  • External diameter: 110 mm
  • Internal height: 42.5 mm
  • External height: 70 mm

Simply slide the sock onto the ram pipes and, when desired, you can secure them in place with a plastic tie-strap.

Please note that we show a ram pipe in the photos but that this is NOT included.

C1052 Enclosed Pipercross Universal Airfilter Socks for Ram Pipes

AFDCOE45
Oval Stainless Steel Airfilter 45 mm tall for Weber DCOE - Dellorto DHLA - Solex ADDHE

Oval Stainless Steel Airfilter 45 mm tall for Weber DCOE - Dellorto DHLA - Solex ADDHE

Great, oval, "pancake" airfilter made of high quality stainless steel.

Suitable for:

  • Weber DCOE 38, 40, 42, 45 and 48
  • Dellorto DHLA 40, 45 and 48
  • Solex ADDHE

Sizes of the oval are 178 x 118 mm.

Thickness: 45 mm

The fixing stud adds some 30 mm to the total thickness.

When using slot-in trumpets in Weber DCOE 48 mm versions, you might have to enlarge the holes in the backing plate to make those fit.

Is being supplied including the gasket hat goes between the filter and the carburettor.

Uses "dry" filter elements, so NOT oiled.

Replacement elements can be found HERE.

Oval Stainless Steel Airfilter 45 mm tall for Weber DCOE - Dellorto DHLA - Solex ADDHE

EMPI8736
Replacement Element for 45 MM Airfilter

Replacement Element for 45 MM Airfilter

Replacement element for our 45 mm tall oval, "pancake" airfilter.

To be used "dry" so NOT oiled.

To be used with our filter reference AFDCOE45.

 

 

 

 

Replacement Element for 45 MM Airfilter

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15 MM
  • 0.25 MM
  • 0.4 MM
  • 0.8 MM
  • 1.6 MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

GREENFUEL8MM-50cm
Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

Alternatively, this hose simply looks great when used with the "Endless band & Buckle" hose clamps like in the photo.

Please note:
This hose is NOT E10 resistant.
Do not use this hose if you are not able to avoid using Ethanol-containing fuels.

Italian style clear green fuel line hose with 8 mm inner diameter

gatestextiel8mm
Gates textile covered fuel line hose with 8 mm inner diameter

Gates textile covered fuel line hose with 8 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

Gates textile covered fuel line hose with 8 mm inner diameter

2134.0600
Cohline E10-resistant fuel line hose with 8 mm inner diameter

Cohline E10-resistant fuel line hose with 8 mm inner diameter

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose.

This fuel hose has an actual inner diameter of 7.5 mm and 13.5 mm outer diameter and therewith a nice and tight fit for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

This hose uses 11 - 13 mm jubilee clips.

Cohline E10-resistant fuel line hose with 8 mm inner diameter

norm5mm
Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide.

Again one of those items that allows you to put the finishing touches on a restoration!

This is the famous "endless band hose clamp with buckle" that was used throughout the 1950's, 1960's and 1970's in the car industry.

Unfortunately, these band clamps are only suitable for one-time use and are discarded after removing them.

Over the years, these clamps have become harder and harder to find but we managed to find a source!

We are selling these in sets.

Such a set consist of the following:

  • Approximately 100 cm Zinc-plated band, 5 millimeters wide
  • 3 buckles

This way, you have roughly a foot (or 33 cm) of band per clamp / buckle which is more than enough for regular applications.

Thanks to the generous length of band, there is virtually no limit to the diameter or circumference of the clamp that you wish to apply although these were usually applied to small diameter fuel lines.

Please note that this style of clamping is NOT suitable for steel-braided lines.

Endless Band Hose Clamp with Buckle - 5 mm wide

jubilee11-13
11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

2134.01.0600
Cohline E10-resistant fuel line hose with 8 mm inner diameter and steel braiding

Cohline E10-resistant fuel line hose with 8 mm inner diameter and steel braiding

This is the top-of-the-line Cohline, steel-braided E10-resistant, flexible fuel line / hose.

This fuel hose has an 8 mm inner diameter and 16 mm outer diameter and is therewith suitable for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

 This hose uses 14 - 16 mm jubilee clips.

Cohline E10-resistant fuel line hose with 8 mm inner diameter and steel braiding

Please note:
This article is currently on order from the manufacturer.
We expect the new supply to arrive at our warehouse by the mid October, 2017.
If you don't want to miss out on it, feel free to place your order now.
Payment is not required until we have your shipment ready to go.

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm - SOLD OUT AT THE MOMENT!

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

Available from our Stock

G4053
Gunson Carbalancer Carburetor Synchronizing Tool

Gunson Carbalancer Carburetor Synchronizing Tool

Gunson Car Balancer.

Internal combustion engines use a mixture of air and petrol to generate their power.

The performance therefore is influenced by the air flowing into it and the petrol that is metered out by the carburettor.

Unless the air flow in Twin or Multiple carburettors is correctly set, the correct mixture adjustment is unlikely to be achieved and this is the simplest tool to achieve that.

Suitable for use on SU, Solex, Auto-Lite (Fomoco), Stromberg, Weber and Zenith and can be adjusted to fit most carburettors including sidedraft, downdraft with air intakes (Venturi) from 25 mm to 67 mm (1”-2”) diameter

  • Easy read scale indicates the air flow and allows adjustment to optimum efficiency
  • Provides smoother and better acceleration
  • Carbalancer can be adjusted to fit most carburettors
  • Easy to follow instructions

The user manual for the Gunson Carbalancer, in English, can be downloaded HERE.

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Carbalancer Carburetor Synchronizing Tool

MANOMETER2
2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easily read scale
  • Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

2 Column Manometer - Synchrometer Carbtune Pro

MANOMETER4
4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easy to read scale
  • Comes complete with 4 x 5 mm and 4 x 6 mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

4 Column Manometer - Synchrometer Carbtune Pro

9679
Brass vacuum take-off adapter for carburetors and manifolds

Brass vacuum take-off adapter for carburetors and manifolds

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Also fits the Weber DCOE series carburettors and Solex ADDHE.

 

Brass vacuum take-off adapter for carburetors and manifolds

SYNCHRONOMETER
Synchrometer airflow meter for carburetors

Synchrometer airflow meter for carburetors

Synchrometer airflow meter for various carburetors.

Pushes into the trumpet / ram pipe / velocity stack or throat to measure the airflow to enable you to balance multiple carburettors.

  • Instructions included
  • The original genuine high quality German made product
  • Can be used for all Weber DCOE and IDF and Dellorto DHLA, DRLA carbs with round intakes or trumpets
  • Can also be used with motorcycle carburetors with round intakes

    Total length of unit 121mm

    Rubber cone dimensions:
    Small end diameter 40mm
    Large end diameter 55mm
    Length of cone 36mm

Synchrometer airflow meter for carburetors