Dellorto DHLB Carburetor Parts
Dellorto DHLB Carburetor Parts

Dellorto DHLB Parts

Dellorto DHLB carburetor parts.

On this page you will find all currently available parts for the Dellorto DHLB range carburettors.

Click HERE for an exploded view drawing of the Dellorto DHLB.

The numbers in the drawing correspond to the numbers in brackets at the beginning of the article description.

Please contact us by email if the part that you are looking for is not listed.

Dellorto DHLB Carburetor Parts

!
DHLBSK
Original Service Kit for 1 Dellorto DHLB Carburetor

Original Service Kit for 1 Dellorto DHLB Carburetor

Service kit suitable for the Dellorto DHLB 32 and DHLB 35 carburetor.

Factory original Dellorto kit.

Contains the parts to service 1 carburetor.

The set consists of the following parts:

  • 1 Pump diaphragm
  • 1 Needle valve, Viton tipped
  • 1 Fuel filter
  • Complete gasket set
  • All required rubber (Viton) o-rings
  • All required aluminum and fiber rings

Original Service Kit for 1 Dellorto DHLB Carburetor

7484
(3) Main jet for Dellorto DHLB carburetors

(3) Main jet for Dellorto DHLB carburetors

Main jet for the Dellorto DHLB series carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available in sizes:

  • 105
  • 110
  • 112
  • 115
  • 118
  • 120
  • 122
  • 125
  • 128
  • 130
  • 132
  • 135
  • 138
  • 140
  • 142
  • 145
  • 150
  • 152
  • 155
  • 158
  • 160
  • 162
  • 165
  • 168
  • 170
  • 172
  • 175
  • 178
  • 180
  • 182
  • 185
  • 190
  • 192
  • 195
  • 198
  • 200
  • 205
  • 210
  • 215
  • 220
  • 225
  • 230
  • 235
  • 240

The above sizes are in stock. The less current sizes are available on special order.

Required quantity per carburettor: 2

This is item number 3 in the drawing.

(3) Main jet for Dellorto DHLB carburetors

4576
(4) Idle Jet for Dellorto DHLB carburetors

(4) Idle Jet for Dellorto DHLB carburetors

Idle jet for for Dellorto DHLB carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available in sizes:

  • 80
  • 85
  • 90

Other sizes are available on request.
Please don't hesitate to contact us with your requirements.

Required quantity per carburettor: 2

This is item number 4 in the drawing.

(4) Idle Jet for Dellorto DHLB carburetors

8083
(6) Pump Jet for Dellorto DHLB carburetors

(6) Pump Jet for Dellorto DHLB carburetors

Pump jet for the Dellorto DHLB series carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available from stock in size 40.

Please contact us by email in case you require other sizes.

Required quantity per carburettor: 2

This is item number 6 in the drawing.

(6) Pump Jet for Dellorto DHLB carburetors

4576
(7) Starter Jet for Dellorto DHLB carburetors

(7) Starter Jet for Dellorto DHLB carburetors

Starter jet for for Dellorto DHLB carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available in sizes:

  • 80
  • 85
  • 90

Other sizes are available on request.
Please don't hesitate to contact us with your requirements.

Required quantity per carburettor: 1

This is item number 7 in the drawing.

(7) Starter Jet for Dellorto DHLB carburetors

7772
(8) Main emulsion tube for Dellorto DHLB carburetors

(8) Main emulsion tube for Dellorto DHLB carburetors

Main emulsion tube for the Dellorto DHLB series carburetors.

Available in types:

  • 7772.1
  • 7772.2
  • 7772.3
  • 7772.4
  • 7772.5
  • 7772.6
  • 7772.7
  • 7772.8
  • 7772.9
  • 7772.10
  • 7772.11
  • 7772.12
  • 7772.13
  • 7772.14
  • 7772.15
  • 7772.16

Required quantity per carburettor: 2

This is item number 8 in the drawing.

(8) Main emulsion tube for Dellorto DHLB carburetors

7482
(10) Starter Emulsion tube for Dellorto DHLB carburetors

(10) Starter Emulsion tube for Dellorto DHLB carburetors

Starter emulsion tube for the Dellorto DHLB series carburetors.

Available in types:

  • 7482.1
  • 7482.2
  • 7482.3
  • 7482.4

Required quantity per carburettor: 1

This is item number 10 in the drawing.

(10) Starter Emulsion tube for Dellorto DHLB carburetors

7485
(11) Air Corrector Jet for Dellorto DHLB carburetors

(11) Air Corrector Jet for Dellorto DHLB carburetors

Air corrector jet for the Dellorto DHLB series carburetors.

We only supply original Dellorto jets, marked with the famous diamond-shaped "Inc" logo.

Available in the following sizes:

  • 120
  • 150
  • 155
  • 160
  • 165
  • 170
  • 175
  • 180
  • 185
  • 187.5
  • 190
  • 192.5
  • 195
  • 200
  • 205
  • 210
  • 215
  • 220
  • 230
  • 240
  • 250
  • 260

The above sizes are in stock. The less current sizes are available on special order. Please contact us with your needs.

Required quantity per carburettor: 2

This is item number 11 in the drawing.

(11) Air Corrector Jet for Dellorto DHLB carburetors

8809
(13) Genuine Viton-Tipped Needle Valve for Dellorto DHLB carburetors

(13) Genuine Viton-Tipped Needle Valve for Dellorto DHLB carburetors

Dellorto DHLB needle valve, seat and aluminum washer.

Genuine Dellorto part, Viton-tipped!

Only genuine Dellorto needles are marked with the diamond shaped "Inc" logo!

Available in sizes:

  • 150
  • 170
  • 200
  • 225
  • 350

Required quantity per carburettor: 1

This is item number 13 in the drawing.

(13) Genuine Viton-Tipped Needle Valve for Dellorto DHLB carburetors

3726
(13) Budget Needle Valve for Dellorto DHLB carburetors

(13) Budget Needle Valve for Dellorto DHLB carburetors

Third party Dellorto DHLB needle valve, seat and aluminium washer.

Solid tip.

Available in size: 175

Required quantity per carburettor: 1

This is item number 13 in the drawing.

(13) Budget Needle Valve for Dellorto DHLB carburetors

7298
(14) Float Assembly for Dellorto DHLB carburetors

(14) Float Assembly for Dellorto DHLB carburetors

Float Assembly Dellorto DHLB series carburetors.

Always replace existing floats with the same version.

Available in the following versions:

  • 7298.1 (8.5 grams, replaces the earlier versions of 9 and 10 grams).
  • 7298.3 (7 grams)

Please note that version 7298.2 is no longer produced. Please use 7298.1 as a replacement.

Required quantity per carburettor: 1

This is item number 14 in the drawing.

(14) Float Assembly for Dellorto DHLB carburetors

6434
(15) Choke Cable Clamp Screw for Dellorto DHLB carburetors

(15) Choke Cable Clamp Screw for Dellorto DHLB carburetors

Choke Cable Clamp Screw for Dellorto DHLB carburetors.

Required quantity per pair of carburettors: 1

This is item number 15 in the drawing.

 

 

(15) Choke Cable Clamp Screw for Dellorto DHLB carburetors

7413
(18) Choke Piston Spring for Dellorto DHLB carburetors

(18) Choke Piston Spring for Dellorto DHLB carburetors

Choke Piston Spring for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 18 in the drawing.

 

 

(18) Choke Piston Spring for Dellorto DHLB carburetors

6425
(22) Needle valve washer for Dellorto DHLB carburetors

(22) Needle valve washer for Dellorto DHLB carburetors

Needle valve washer for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 22 in the drawing.

 

 

(22) Needle valve washer for Dellorto DHLB carburetors

7549
(23) Jet Cover for Dellorto DHLB carburetors - Black Plastic

(23) Jet Cover for Dellorto DHLB carburetors - Black Plastic

Jet Cover for Dellorto DHLB series carburetors.

This is the black plastic version.

Please note that the earlier white plastic version is are no longer available.

Required quantity per carburettor: 1

This is item number 23 in the drawing.

(23) Jet Cover for Dellorto DHLB carburetors - Black Plastic

7549M
(23) Jet Cover for Dellorto DHLB carburetors - Metal

(23) Jet Cover for Dellorto DHLB carburetors - Metal

Jet Cover for Dellorto DHLB series carburetors.

This is the metal version which has been taken into re-production after a long absence.

Required quantity per carburettor: 1

This is item number 25 in the drawing.

(23) Jet Cover for Dellorto DHLB carburetors - Metal

7530
(24) Jet Cover Screw for Dellorto DHLB carburetors

(24) Jet Cover Screw for Dellorto DHLB carburetors

Jet Cover Screw for Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 24 in the drawing.

 

 

(24) Jet Cover Screw for Dellorto DHLB carburetors

5011
(25) Spring Washer for Dellorto DHLB carburetors

(25) Spring Washer for Dellorto DHLB carburetors

Spring Washer for the jet cover of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 25 in the drawing.

 

 

(25) Spring Washer for Dellorto DHLB carburetors

14231
(26) Top Casing Screw for Dellorto DHLB carburetors

(26) Top Casing Screw for Dellorto DHLB carburetors

Screw for, amongst others, the top casting of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 4

This is item number 26 in the drawing.

 

 

(26) Top Casing Screw for Dellorto DHLB carburetors

4997
(27) Spring Washer for Dellorto DHLB carburetors

(27) Spring Washer for Dellorto DHLB carburetors

Spring washer for, amongst others, the top casting of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 4

This is item number 27 in the drawing.

 

(27) Spring Washer for Dellorto DHLB carburetors

8047
(28) Jet Cover Gasket for Dellorto DHLB carburetors
(28) Jet Cover Gasket for Dellorto DHLB carburetors

(28) Jet Cover Gasket for Dellorto DHLB carburetors

This gasket is no longer available!

Required quantity per carburettor: 1

This is item number 28 in the drawing.

 

 

(28) Jet Cover Gasket for Dellorto DHLB carburetors

7062
(29) Choke Cable Bolt for Dellorto DHLB carburetors

(29) Choke Cable Bolt for Dellorto DHLB carburetors

Special, hollow and cross-drilled, choke cable bolt for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 29 in the drawing.

 

(29) Choke Cable Bolt for Dellorto DHLB carburetors

6850
(30) Choke Cable Washer for Dellorto DHLB carburetors

(30) Choke Cable Washer for Dellorto DHLB carburetors

Choke Cable Washer for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 30 in the drawing.

 

 

(30) Choke Cable Washer for Dellorto DHLB carburetors

6432
(31) Choke Cable Nut for Dellorto DHLB carburetors

(31) Choke Cable Nut for Dellorto DHLB carburetors

Special shape choke cable nut for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 31 in the drawing.

 

 

(31) Choke Cable Nut for Dellorto DHLB carburetors

7854
(36) Choke Return Spring for Dellorto DHLB carburetors

(36) Choke Return Spring for Dellorto DHLB carburetors

Choke Return Spring for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 36 in the drawing.

 

 

(36) Choke Return Spring for Dellorto DHLB carburetors

7838
(37) Choke return spring cup washer for Dellorto DHLB carburetors

(37) Choke return spring cup washer for Dellorto DHLB carburetors

Choke return spring cup washer for the Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 37 in the drawing.

 

 

(37) Choke return spring cup washer for Dellorto DHLB carburetors

4957
(38) Spring washer for Choke Mechanism on Dellorto DHLB carburetors

(38) Spring washer for Choke Mechanism on Dellorto DHLB carburetors

Spring washer for Choke Mechanism on Dellorto DHLB carburetors.

Required quantity per carburettor: 1

This is item number 38 in the drawing.

 

 

(38) Spring washer for Choke Mechanism on Dellorto DHLB carburetors

2906
(39) Choke Nut for Dellorto DHLB carburetors

(39) Choke Nut for Dellorto DHLB carburetors

Nut for the choke mechanism on the Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 39 in the drawing.

 

 

(39) Choke Nut for Dellorto DHLB carburetors

7503
(40) Float pivot pin for Dellorto DHLB carburetors

(40) Float pivot pin for Dellorto DHLB carburetors

Float pivot pin for Dellorto DHLB carburetors.

Required quantity per carburettor: 1

This is item number 40 in the drawing.

 

 

(40) Float pivot pin for Dellorto DHLB carburetors

7659
(41) Fuel banjo bolt for Dellorto DHLB carburetors

(41) Fuel banjo bolt for Dellorto DHLB carburetors

Fuel banjo bolt for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 41 in the drawing.

 

 

(41) Fuel banjo bolt for Dellorto DHLB carburetors

7662
(42) Outer fuel banjo fiber washer for Dellorto DHLB carburetors

(42) Outer fuel banjo fiber washer for Dellorto DHLB carburetors

Outer fuel banjo fiber washer for Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 42 in the drawing.

 

 

(42) Outer fuel banjo fiber washer for Dellorto DHLB carburetors

1419
(43) Fuel banjo filter for Dellorto DHLB carburetors

(43) Fuel banjo filter for Dellorto DHLB carburetors

Fuel banjo filter for Dellorto DHLB series carburetors.

This filter measures 14 mm in height.

Required quantity per carburettor: 1

This is item number 43 in the drawing.

 

(43) Fuel banjo filter for Dellorto DHLB carburetors

7663
(45) Lower fuel banjo fibre washer for Dellorto DHLB carburetors

(45) Lower fuel banjo fibre washer for Dellorto DHLB carburetors

Lower fuel banjo fibre washer for the Dellorto DHLBA series carburetors.

Required quantity per carburettor: 1

This is item number 45 in the drawing.

 

 

(45) Lower fuel banjo fibre washer for Dellorto DHLB carburetors

10747
(47) Pump jet holder for Dellorto DHLB carburetors

(47) Pump jet holder for Dellorto DHLB carburetors

Pump jet holder for Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 47 in the drawing.

 

 

(47) Pump jet holder for Dellorto DHLB carburetors

6173
(48) Pump jet o-ring for Dellorto DHLB carburetors

(48) Pump jet o-ring for Dellorto DHLB carburetors

Pump jet o-ring for Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 48 in the drawing.

 

 

(48) Pump jet o-ring for Dellorto DHLB carburetors

6426
(49) Fiber Ring for Dellorto DHLB carburetors

(49) Fiber Ring for Dellorto DHLB carburetors

Fiber ring for the pump jet holder for the Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 49 in the drawing.

 

 

(49) Fiber Ring for Dellorto DHLB carburetors

8176
(50) Air Bleed Screw for Dellorto DHLB carburetors

(50) Air Bleed Screw for Dellorto DHLB carburetors

Airbleed Screw for the Dellorto DHLB series carburetors.

Please note that not every DHLB has these screws fitted.

This particular variation uses nor an o-ring, nor a locking nut.

Required quantity per carburettor: 2

This is item number 50 in the drawing.

(50) Air Bleed Screw for Dellorto DHLB carburetors

7525
(53) Pump jet weight for Dellorto DHLB carburetors

(53) Pump jet weight for Dellorto DHLB carburetors

Pump jet weight for Dellorto DHLB series carburetors.

Please note that there are in total three versions of this weight of which (unfortunately!) only 1 version is still available.

This particular version (7525) IS available!

Required quantity per carburettor: 2

This is item number 53 in the drawing.

(53) Pump jet weight for Dellorto DHLB carburetors

6415
(54) Pump jet ball bearing for Dellorto DHLB carburetors

(54) Pump jet ball bearing for Dellorto DHLB carburetors

Pump jet ball bearing for Dellorto DHLB series carburetors.

Ball bearing of the correct weight and size for the pump mechanism.

Required quantity per carburettor: 2

This is item number 54 in the drawing.

 

(54) Pump jet ball bearing for Dellorto DHLB carburetors

7959
(55) Vacuum Blanking Screw for Dellorto DHLB carburetors

(55) Vacuum Blanking Screw for Dellorto DHLB carburetors

Vacuum Blanking Screw for the Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 55 in the drawing.

 

 

(55) Vacuum Blanking Screw for Dellorto DHLB carburetors

4670
(57) Mixture screw spring for Dellorto DHLB carburetors

(57) Mixture screw spring for Dellorto DHLB carburetors

Mixture screw spring for Dellorto DHLB carburetors.

Required quantity per carburettor: 2

This is item number 57 in the drawing.

 

 

(57) Mixture screw spring for Dellorto DHLB carburetors

4650
(58) Mixture Screw Washer for Dellorto DHLB carburetors

(58) Mixture Screw Washer for Dellorto DHLB carburetors

Mixture Screw Washer for Dellorto DHLB carburetors.

Required quantity per carburettor: 2

This is item number 58 in the drawing.

 

 

(58) Mixture Screw Washer for Dellorto DHLB carburetors

7540
(59) Mixture Screw O ring for Dellorto DHLB carburetors

(59) Mixture Screw O ring for Dellorto DHLB carburetors

Viton O-ring to seal the mixture screws on the Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 59 in the drawing.

 

 

(59) Mixture Screw O ring for Dellorto DHLB carburetors

6423
(60) Spindle Nut for Dellorto DHLB carburetors

(60) Spindle Nut for Dellorto DHLB carburetors

Spindle nut for the Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 60 in the drawing.

 

 

(60) Spindle Nut for Dellorto DHLB carburetors

6581
(61) Spindle Nut Lock Washer for Dellorto DHLB carburetors

(61) Spindle Nut Lock Washer for Dellorto DHLB carburetors

Spindle Nut Lock Washer for Dellorto DHLB carburetors.

Required quantity per carburettor: 2

This is item number 61 in the drawing.

 

 

(61) Spindle Nut Lock Washer for Dellorto DHLB carburetors

7537
(64) Spindle washer for Dellorto DHLB carburetors

(64) Spindle washer for Dellorto DHLB carburetors

Spindle washer for Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 64 in the drawing.

 

 

(64) Spindle washer for Dellorto DHLB carburetors

7490
(65) Spindle bearing for Dellorto DHLB carburetors

(65) Spindle bearing for Dellorto DHLB carburetors

Spindle bearing for Dellorto DHLB carburetors.

Sealed and lubricated for life.

Required quantity per carburettor: 2

This is item number 65 in the drawing.

 

 

 

(65) Spindle bearing for Dellorto DHLB carburetors

55555.010
(66) Spindle End Cover for Dellorto DHLB carburetors

(66) Spindle End Cover for Dellorto DHLB carburetors

Spindle end cover for Dellorto DHLB series carburetors.

Required quantity per carburettor: 2

This is item number 66 in the drawing.

 

 

 

 

(66) Spindle End Cover for Dellorto DHLB carburetors

4997
(69) Spring Washer for Dellorto DHLB carburetors

(69) Spring Washer for Dellorto DHLB carburetors

Spring washer for, amongst others, the pump body casting of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 4

This is item number 69 in the drawing.

 

(69) Spring Washer for Dellorto DHLB carburetors

4670
(73) Balance Screw Spring for Dellorto DHLB carburetors

(73) Balance Screw Spring for Dellorto DHLB carburetors

Balance Screw Spring for Dellorto DHLB series carburetors.

This spring "loads" the balance screw on the DHLB series and thus locks your setting.

Required quantity per set of 2 carburettors: 1

This is item number 73 in the drawing.

 

(73) Balance Screw Spring for Dellorto DHLB carburetors

4650
(74) Throttle Stop Screw Washer for Dellorto DHLB carburetors

(74) Throttle Stop Screw Washer for Dellorto DHLB carburetors

Throttle Stop Screw Washer for Dellorto DHLB series carburetors.

Required quantity per set of carburettors: 1

This is item number 74 in the drawing.

 

 

(74) Throttle Stop Screw Washer for Dellorto DHLB carburetors

7540
(75) Throttle Stop Screw O ring for Dellorto DHLB carburetors

(75) Throttle Stop Screw O ring for Dellorto DHLB carburetors

Viton O-ring for the throttle stop screw on the Dellorto DHLB series carburetors.

Required quantity per carburetor: 1

This is item number 75 in the drawing.

 

 

(75) Throttle Stop Screw O ring for Dellorto DHLB carburetors

6898
(76) Balance Lever Screw for Dellorto DHLB carburetors

(76) Balance Lever Screw for Dellorto DHLB carburetors

Balance Lever Screw for Dellorto DHLB series carburetors.

Adjusts the balance between carburetors.

Required quantity per set carburettors: 1

This is item number 76 in the drawing.

 

(76) Balance Lever Screw for Dellorto DHLB carburetors

9752
(78) Balance Lever Pin for Dellorto DHLB carburetors

(78) Balance Lever Pin for Dellorto DHLB carburetors

Balance Lever Pin for Dellorto DHLB series carburetors.

Required quantity per set of 2 carburettors: 1

This is item number 80 in the drawing.

 

 

(78) Balance Lever Pin for Dellorto DHLB carburetors

3793
(79) Split Pin for balance lever on Dellorto DHLB carburetors

(79) Split Pin for balance lever on Dellorto DHLB carburetors

Split Pin for the balance lever on the Dellorto DHLB series carburetors.

Required quantity per set of carburettors: 1

This is item number 79 in the drawing.

 

 

(79) Split Pin for balance lever on Dellorto DHLB carburetors

2638
(80) Balance Lever Spring for Dellorto DHLB carburetors

(80) Balance Lever Spring for Dellorto DHLB carburetors

Balance Lever Spring for Dellorto DHLB series carburetors.

This spring dampens the movement of the balance screw on the DHLB series.

Required quantity per set of 2 carburettors: 1

This is item number 80 in the drawing.

 

(80) Balance Lever Spring for Dellorto DHLB carburetors

9673
(84) Pump Diaphragm for Dellorto DHLB carburetors

(84) Pump Diaphragm for Dellorto DHLB carburetors

Replacement diaphragm for the pump jet pump on the Dellorto DHLB series carburetors.

Please note that there are different versions available of this diaphragm, with the metal disk on this one measuring 19 mm in diameter.

Required quantity per carburettor: 1

This is item number 84 in the drawing.

(84) Pump Diaphragm for Dellorto DHLB carburetors

5011
(86) Spring Washer for Dellorto DHLB carburetors

(86) Spring Washer for Dellorto DHLB carburetors

Spring Washer for the pump body cover of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 4

This is item number 86 in the drawing.

 

 

(86) Spring Washer for Dellorto DHLB carburetors

6429
(87) Screw for Dellorto DHLB carburetors

(87) Screw for Dellorto DHLB carburetors

Screw for the pump cover of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 4

This is item number 87 in the drawing.

 

 

(87) Screw for Dellorto DHLB carburetors

6390
(88) Pump Rod Adjuster Nut for Dellorto DHLB carburetors

(88) Pump Rod Adjuster Nut for Dellorto DHLB carburetors

Adjuster nut for setting the pump rod on the Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 88 in the drawing.

 

 

(88) Pump Rod Adjuster Nut for Dellorto DHLB carburetors

6390
(89) Lock Nut for Pump Rod Adjuster on Dellorto DHLB carburetors

(89) Lock Nut for Pump Rod Adjuster on Dellorto DHLB carburetors

Lock nut to secure the setting of the pump rod on the Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 89 in the drawing.

 

(89) Lock Nut for Pump Rod Adjuster on Dellorto DHLB carburetors

7542
(92) Pump Non-Return Valve for Dellorto DHLB carburetors

(92) Pump Non-Return Valve for Dellorto DHLB carburetors

Pump Non-Return Valve for Dellorto DHLB carburetors.

No return valve (one way) for the pump mechanism.

Required quantity per carburettor: 1

This is item number 92 in the drawing.

 

(92) Pump Non-Return Valve for Dellorto DHLB carburetors

7540
(93) Pump Valve O ring for Dellorto DHLB carburetors

(93) Pump Valve O ring for Dellorto DHLB carburetors

Viton O-ring to seal the pump valve on the Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 93 in the drawing.

 

 

(93) Pump Valve O ring for Dellorto DHLB carburetors

7526
(96) Screw for Dellorto DHLB carburetors

(96) Screw for Dellorto DHLB carburetors

Screw for the pump housing of the Dellorto DHLB series carburetors.

Required quantity per carburettor: 4

This is item number 96 in the drawing.

 

 

(96) Screw for Dellorto DHLB carburetors

6416
(97) Butterfly screw for Dellorto DHLB carburetors

(97) Butterfly screw for Dellorto DHLB carburetors

Butterfly screw for Dellorto DHLB series carburetors.

When replacing your butterfly valves, ALWAYS use new screws, use a locking agent AND peen them to secure them in place.

NEVER re-use old screws!

Required quantity per carburettor: 4

This is item number 97 in the drawing.

(97) Butterfly screw for Dellorto DHLB carburetors

7667
(99) Pump Rod Clamp Screw for Dellorto DHLB carburetors

(99) Pump Rod Clamp Screw for Dellorto DHLB carburetors

Screw to secure the pump rod clamp to the pump rod on the Dellorto DHLB series carburetors.

Required quantity per carburettor: 1

This is item number 99 in the drawing.

 

(99) Pump Rod Clamp Screw for Dellorto DHLB carburetors

cosx4
Cosworth mounts - carburetor to manifold

Cosworth mounts - carburetor to manifold

Developed by British-based racing engineers Cosworth, these buffers are specifically designed to be used in conjunction with Misab-plates.

The mounts are strong enough to ensure an airtight seal while also providing enough vibration damping.

Each mount consists of two cups and one rubber buffer.

Install the Misab-plates, install your carb(s), install the Cosworth mounts using a Nyloc nut (NOT included!) and set the distance between the cups to 2 millimeter, using a normal feeler gauge.

These mounts are supplied in sets of 4 complete mounts (as depicted) which is enough for one carburettor like a Dellorto DHLA or Weber DCOE.

Cosworth mounts - carburetor to manifold

MISAB
Original Misab Plates carburetor mounts

Original Misab Plates carburetor mounts

Developed by MIS AB in Sweden, these mounts are specifically designed to be used in conjunction with the Cosworth buffer mounts.

These plates ensure ensure an airtight seal between carburettor and manifold, thanks to their vulcanized rubber ring.

These MISAB plates are supplied in sets of 2 which is enough for one carburettor like a Dellorto DHLA or Weber DCOE.

Original Misab Plates carburetor mounts

FK85
Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Metal Bowl

Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Metal Bowl

Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Metal Bowl.

  • Fuel pressure can be regulated between 1.5 PSI and 5 PSI (0.1 - 0.35 Bar).
  • Regularly used in motorsport due to its ability to regulate and filter fuel without restriction.
  • Suitable for engines of over 150 BHP.
  • Competition model with metal bowl to avoid the risk of breakage.
  • Provision for the fitting of a pressure gauge; blanking plug supplied.
  • Replacement filters available HERE.
  • Brass in / out unions suitable for 5/16th - 8mm fuel pipe.
  • Instructions, mounting bracket and bolts included.

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

The Fitting Kit is also available separately.

Spare, brass, blanking plugs can be found HERE.

Spare Cast Metal Bowls are available HERE.
Alternatively, a clear glass bowl is also available.

Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Metal Bowl

FK85/T
Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Clear Glass Bowl

Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Clear Glass Bowl

Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Clear Glass Bowl.

  • Fuel pressure can be regulated between 1.5 PSI and 5 PSI (0.1 - 0.35 Bar).
  • Regularly used in motorsport due to its ability to regulate and filter fuel without restriction.
  • Suitable for engines of over 150 BHP.
  • Competition model with a clear glass bowl that allows to quickly inspect the condition of the filter element.
  • Provision for the fitting of a pressure gauge; blanking plug supplied.
  • Replacement filters available HERE.
  • Brass in / out unions suitable for 5/16th - 8mm fuel pipe.
  • Instructions, mounting bracket and bolts included.

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

The Fitting Kit is also available separately.

Spare, brass, blanking plugs can be found HERE.

Spare Clear Glass Bowls are available HERE.
Alternatively, a cast metal bowl is also available.

Malpassi Filter King Fuel Filter and Pressure Regulator 85 mm with Clear Glass Bowl

FPG001
Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar.

Low pressure fuel pressure gauge.

Ideal for setting the pressure on systems with carburettors.

Can be used with the 85mm Filter King filter and pressure regulator or our Fuel Pressure Gauge Adapter.

Range:

  • 0 - 15 PSI
  • 0 - 1 Bar

Thread: 1/8th" tapered NPTF.

Note:
This gauge should only be used for setting-up and then be removed for normal running.
NOT suited for high-pressure (fuel injected) systems!

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

Sytec Fuel Pressure Gauge 0 - 15 PSI / 0 - 1 Bar

PRO805
Sytec Pro-Line in-line fuel filter - 8 mm

Sytec Pro-Line in-line fuel filter - 8 mm

In line fuel filter with cleanable / replaceable filter.

Suitable for 8 mm internal diameter fuel hoses.

Replacement filter elements are available HERE.

Chrome finish.

Toughened glass phial.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

Supplied with 2 Jubilee clips.

Couplings Specifications:
Fuel Unions for fuel lines with 8 mm internal diameter

Sytec Pro-Line in-line fuel filter - 8 mm

PRO896
Replacement elements for Sytec in-line fuel filter

Replacement elements for Sytec in-line fuel filter

3 replacement elements for the Sytec Pro-Line in-line fuel filter.

Come complete with new rubber seals.

These elements fit our PRO804 and PRO805 Sytec in-line fuel filters.

Suitable for system pressures of up to 10 PSI / 0.7 Bar.

 

 

 

 

Replacement elements for Sytec in-line fuel filter

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15MM
  • 0.25MM
  • 0.4MM
  • 0.8MM
  • 1.6MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

GREENFUEL8MM-50cm
Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter

Italian style clear green fuel line hose with 8 mm inner diameter.

This is the perfect finisher for a successful restoration!

This fuel hose has an 8 mm inner diameter and 11 mm outer diameter.

It is sold in lengths of 50 cm (19.7 inch).

When ordering multiple lengths, we will do our utmost to supply that as 1 piece.

This hose uses 10 - 12 mm jubilee clips.

Italian style clear green fuel line hose with 8 mm inner diameter

gatestextiel8mm
Gates textile covered fuel line hose with 8 mm inner diameter

Gates textile covered fuel line hose with 8 mm inner diameter

Newly arrived Gates textile covered fuel line hose with 8 mm inner diameter

This is the top-of-the-line Gates flexible fuel line, resistant to modern day, aggressive, fuels.

Textile covered for the correct "vintage" look.

This fuel hose has an 8 mm inner diameter and 13 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

This small-diameter hose has a durable and oil resistant textile cover that provides a dependable and safe service on fuel circuits in passenger cars.

This hose is resistant to heat, leaded and unleaded fuels, oil and Diesel.
Please note that E10 fuel resistance is NOT mentioned by the manufacturer!

Recommended for clamped hose applications on low-pressure (carburetor) fuel systems in passenger cars.
NOT suited for high pressure fuel injection systems.

Key Features and Benefits:

• The tube resists heat, fuel (leaded and unleaded petrol, diesel) and oil
• The braided textile cover reinforces the hose and is resistant to heat, ozone and weathering
• Working pressure up to 0.6 MPa (6 kg/cm²)
• Temperature range from -35°C to +100°C

Maximum, single, length: 15 meters.

This hose uses 11 - 13 mm jubilee clips.

Gates textile covered fuel line hose with 8 mm inner diameter

2134.0600
Cohline E10-resistant fuel line hose with 8 mm inner diameter

Cohline E10-resistant fuel line hose with 8 mm inner diameter

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose.

This fuel hose has an actual inner diameter of 7.5 mm and 13.5 mm outer diameter and therewith a nice and tight fit for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

This hose uses 11 - 13 mm jubilee clips.

Cohline E10-resistant fuel line hose with 8 mm inner diameter

norm5mm
Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide.

Again one of those items that allow you to put the finishing touches on a restoration!

This is the famous "endless band hose clamp with buckle" that was used throughout the 1950's, 1960's and 1970's in the car industry.

Unfortunately, these band clamps are only suitable for one-time use and are discarded after removing them.

Over the years, these clamps have become harder and harder to find but we managed to find a source!

We are selling these in sets of 3.

Such a set consist of the following:

  • Approximately 100 cm Zinc-plated band, 5 millimeters wide
  • 3 buckles

This way, you have roughly a foot (or 33 cm) of band per clamp / buckle which is more than enough for regular applications.

Thanks to the generous length of band, there is virtually no limit to the diameter or circumference of the clamp that you wish to apply although these were usually applied to small diameter fuel lines.

Please note that this style of clamping is NOT suitable for stainless steel-braided lines.

Endless Band Hose Clamp with Buckle - 5 mm wide

jubilee11-13
11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp for 8 mm Flexible Fuel Line.

This hose clamp (or jubilee clip) is perfectly suited for our 8 mm internal diameter fuel line.

Neatly finished, the stainless steel (Grade 304) makes it the perfect compliment to our textile covered fuel hose.

It is rated for between 8 mm internal diameter (i.e. 11 - 13 mm external hose diameter).

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

11 - 13 mm Stainless Steel Jubilee Clip Hose Clamp

2134.01.0600
Cohline E10-resistant fuel line hose with 8 mm inner diameter and stainless steel braiding

Cohline E10-resistant fuel line hose with 8 mm inner diameter and stainless steel braiding

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose with stainless steel braiding.

This fuel hose has an 8 mm inner diameter and 16 mm outer diameter and is therewith suitable for 8 mm fuel unions.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

Cohline E10-resistant fuel line hose with 8 mm inner diameter and stainless steel braiding

OWV
Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve

Sytec Fuel Line One Way Valve.

We have two versions available:

  • Suitable for 6 mm internal diameter fuel hoses
  • Suitable for 8 mm internal diameter fuel hoses

Silver anodized finish.

Prevents fuel from leaking back into the fuel tank.

Suitable for regular fuel, E10, E85 and Diesel.

Viton seals.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

Sytec Fuel Line One Way Valve

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

 

Jet size gauge 0.5 to 1.5 mm

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol / LPG 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Additional Information

  • Kit includes: 14mm Short reach plug and Hexagonal adapter
  • Colortune will fit most vehicles
  • Kit complete with instructions in English
  • Extra adapter sizes available separately

Available in the following basic sizes:

  • 10 mm - Available from our Stock
  • 12 mm - Sold out at the moment !
  • 14 mm - Available from our Stock

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Colortune See Through Spark Plug Kit

Available as long as our limited stock lasts!

G4053
Gunson Carbalancer Carburetor Synchronizing Tool

Gunson Carbalancer Carburetor Synchronizing Tool

Gunson Car Balancer.

Internal combustion engines use a mixture of air and petrol to generate their power.

The performance therefore is influenced by the air flowing into it and the petrol that is metered out by the carburettor.

Unless the air flow in Twin or Multiple carburettors is correctly set, the correct mixture adjustment is unlikely to be achieved and this is the simplest tool to achieve that.

Suitable for use on SU, Solex, Auto-Lite (Fomoco), Stromberg, Weber and Zenith and can be adjusted to fit most carburettors including sidedraft, downdraft with air intakes (Venturi) from 25 mm to 67 mm (1”-2”) diameter

  • Easy read scale indicates the air flow and allows adjustment to optimum efficiency
  • Provides smoother and better acceleration
  • Carbalancer can be adjusted to fit most carburettors
  • Easy to follow instructions

The user manual for the Gunson Carbalancer, in English, can be downloaded HERE.

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Carbalancer Carburetor Synchronizing Tool

MANOMETER2
2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easily read scale
  • Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

2 Column Manometer - Synchrometer Carbtune Pro

MANOMETER4
4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easy to read scale
  • Comes complete with 4 x 5 mm and 4 x 6 mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off can be found HERE.

4 Column Manometer - Synchrometer Carbtune Pro

9679
Brass vacuum take-off adapter for carburetors and manifolds

Brass vacuum take-off adapter for carburetors and manifolds

Vacuum take-off adapter for Dellorto DHLA and PHF.

Vacuum take off adapter, will fit standard take off point of DHLA carburetors, DHLB carburettors, and PHF carburettors.

Also fits the Weber DCOE series carburettors and Solex ADDHE.

 

Brass vacuum take-off adapter for carburetors and manifolds

SYNCHRONOMETER
Synchrometer airflow meter for carburetors

Synchrometer airflow meter for carburetors

Synchrometer airflow meter for various carburetors.

Pushes into the trumpet / ram pipe / velocity stack or throat to measure the airflow to enable you to balance multiple carburettors.

  • Instructions included
  • The original genuine high quality German made product
  • Can be used for all Weber DCOE and IDF and Dellorto DHLA, DRLA carbs with round intakes or trumpets
  • Can also be used with motorcycle carburetors with round intakes

    Total length of unit 121mm

    Rubber cone dimensions:
    Small end diameter 40mm
    Large end diameter 55mm
    Length of cone 36mm

Synchrometer airflow meter for carburetors

SYNCELBOW
Synchrometer adapter elbow

Synchrometer adapter elbow

Rubber adapter hose to allow use of the Synchrometer in confined spaces.

Approx. overall length 150mm.

External diameter at carburetor end 40mm.

Internal diameter at Synchrometer end 43mm.

 

Synchrometer adapter elbow

DD0906
Dellorto Carburatori Sticker - Large

Dellorto Carburatori Sticker - Large

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 9 x 3 cm (3.54 x 1.2 inches).

This is Number 1 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Large

DD0909
Dellorto Carburatori Sticker - Medium

Dellorto Carburatori Sticker - Medium

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 8 x 4 cm (3.1 x 1.55 inches).

This is Number 2 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Medium

DD0904
Dellorto Carburatori Sticker - Small - High

Dellorto Carburatori Sticker - Small - High

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 6 x 3 cm (2.4 x 1.2 inches).

This is Number 3 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Small - High

DD0905
Dellorto Carburatori Sticker - Small - Low

Dellorto Carburatori Sticker - Small - Low

Official issue sticker / decal with the Dellorto logo and Italian flag "tricolore" colors.

Measures 6 x 2 cm (2.4 x 0.8 inches).

This is Number 4 in the photograph.

Made of high quality vinyl.

 

 

 

Dellorto Carburatori Sticker - Small - Low

Patch
Dellorto Carburatori Sew-On Patch

Dellorto Carburatori Sew-On Patch

Official issue sew-on patch with the Dellorto logo and Italian flag "tricolore" colors.

Measures 12 x 6.5 cm (4.7 x 2.6 inches).

Elaborately embroidered.

 

 

Dellorto Carburatori Sew-On Patch