Facet CUBE Solid State Fuel Pumps
Facet CUBE Solid State Fuel Pumps

Facet CUBE Solid State Fuel Pumps

Facet CUBE Solid State Fuel Pumps.

To make life a little easier for you and to save you from having to make your way through dozens of model designations, we have sorted the Facet CUBE pumps according to their performance.

So, to keep things simple:

Facet Cube ROAD - for engines up to some 130 BHP
Facet Cube FAST ROAD - for engines up to some 150 BHP
Facet Cube COMPETITION - for engines up to 180 BHP

You will find the various pumps listed below, according to this designation.

Each of these pumps is available as a single pump body or as a complete kit with connectors and mounting material.

Engineered without bearings, electrical contacts or diaphragms to wear out or fatigue, Facet CUBE Solid State electronic fuel pumps deliver the quality, long lasting performance and reliability demanded by the toughest users.

  • Fuel Compatibility:
    All models of the Facet® CUBE® Fuel Pumps are compatible with gasoline, diesel, biodiesel, E85, blended alcohol fuels and fuel additives.
  • Solid State Reliability:
    Proven on thousands of original equipment applications.
    No electrical contacts.
    No bearings or diaphragms to wear out or fatigue.
    Lasts four to five times longer than many other electric fuel pumps.
  • Easy to Install:
    Two-bolt installation plus the small size makes installation easy.
    For best results, mount the pump close to the fluid or fuel tank and below the liquid level.
  • Eliminates Vapor Lock:
    When properly installed on most vehicles a constant, smooth, dependable supply of fuel under pressure is assured in the hottest weather or in high altitudes.

These self-priming and self-regulating fuel pumps are designed for use on all low- and high-pressure carburetter-equipped vehicles, vans, trucks, generators, agricultural, gasoline and diesel engines, marine, construction and utility equipment.

These CUBE pumps feature:

  • State-of-the-Art Electronics
  • Sealed Electronics
  • Internal Check Valve
  • Reverse Polarity Protection
  • 1.4 Amp Average
  • Corrosion resistant to 100 hours of salt spray
  • Easy 2-Bolt Mounting
  • Self-regulating Pressure
  • Internal Anti-Syphon Valve
  • Compatible with Gasoline, Diesel, Biodiesel, E85, Blended Alcohol and Fuel Additives

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

The Facet CUBE pumps that we carry use a 1/8" NPFT tapered thread for the connectors.
You will find the available connectors HERE.

Facet CUBE Solid State Fuel Pumps

!
SSRK
Facet CUBE Solid State ROAD Fuel Pump Kit

Facet CUBE Solid State ROAD Fuel Pump Kit

Facet Solid State ROAD Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State ROAD fuel pump is suitable for engines of up to circa 130 HP.

Pump specification:

  • Flow rate 12 Gallons/hour - 45 liters/hour
  • Pressure: 2.5 - 3.0 PSI - 0.17 - 0.20 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State ROAD Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State ROAD Fuel Pump Kit

SSR
Facet CUBE Solid State ROAD Fuel Pump - Pump Only

Facet CUBE Solid State ROAD Fuel Pump - Pump Only

Facet CUBE Solid State ROAD Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State ROAD fuel pump is suitable for engines of up to circa 130 HP.

Pump specification:

  • Flow rate 12 Gallons/hour - 45 liters/hour
  • Pressure: 2.5 - 3.0 PSI - 0.17 - 0.20 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State ROAD Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State ROAD Fuel Pump - Pump Only

SSFRK
Facet CUBE Solid State FAST ROAD Fuel Pump Kit

Facet CUBE Solid State FAST ROAD Fuel Pump Kit

Facet Solid State FAST ROAD Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State FAST ROAD fuel pump is suitable for engines of up to circa 150 HP.

Pump specification:

  • Flow rate 32 Gallons/hour - 120 liters / hour
  • Pressure: 4 - 7 PSI - 0.27 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State FAST ROAD Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State FAST ROAD Fuel Pump Kit

SSFR
Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

Facet CUBE Solid State FAST ROAD Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State FAST ROAD fuel pump is suitable for engines of up to circa 150 HP.

Pump specification:

  • Flow rate 32 Gallons/hour - 120 liters / hour
  • Pressure: 4 - 7 PSI - 0.27 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State FAST ROAD Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State FAST ROAD Fuel Pump - Pump Only

SSCK
Facet CUBE Solid State COMPETITION Fuel Pump Kit

Facet CUBE Solid State COMPETITION Fuel Pump Kit

Facet Solid State COMPETITION Fuel Pump Kit.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State COMPETITION fuel pump is suitable for engines of up to circa 180 HP.

Pump specification:

  • Flow rate 25 Gallons/hour - 95 liters/hour
  • Pressure: 6.0 - 7.0 PSI - 0.41 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Kit includes:

  • Pump
  • 2 Mounting isolation feet
  • 8 mm Outlet Union
  • Screw-on inlet filter
  • Installation instructions

Please note that failure to operate the pump with a suitable filter voids the warranty!

Replacement filters can be found HERE.

These kits are usually purchased to modify an existing system or to replace an existing mechanical fuel pump.
In case you just want to replace a broken pump of this same type, we advise you to take a look at our Facet CUBE Solid State COMPETITION Fuel Pump - pump only.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Unions for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State COMPETITION Fuel Pump Kit

SSC
Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

Facet CUBE Solid State COMPETITION Fuel Pump only.

Using Facet's proven "CUBE Solid State" technology, the CUBE Solid State COMPETITION fuel pump is suitable for engines of up to circa 180 HP.

Pump specification:

  • Flow rate 25 Gallons/hour - 95 liters/hour
  • Pressure: 6.0 - 7.0 PSI - 0.41 - 0.48 Bar
  • Dry prime height 1 Ft - 0.3 Mtrs
  • Pipe union thread size: 1/8" NPTF tapered thread
  • 12 Volt negative earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol

Please note that failure to operate the pump with a suitable filter voids the warranty!

Suitable screw-on filters can be found HERE.

Please note: this concerns ONLY the pump body... no further connectors or mounting material!

These single pumps are usually purchased to replace a broken pump.
In case you want to equip your vehicle with such an electrical pump system, we advise you to take a look at our Facet CUBE Solid State COMPETITION Fuel Pump Kit.

Depending on your vehicle's carburetors and the Facet CUBE pump of your choice, it might be required to use a pressure regulator.
Please check the CUBE specifications against the requirements of your vehicle to be sure.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

When using an electrical fuel pump, we also advise you to equip your vehicle with an Inertia Fuel Cut-Off Switch as a safety precaution.

Facet CUBE Solid State COMPETITION Fuel Pump - Pump Only

FPA905
Facet Fuel Pump Mounting Kit

Facet Fuel Pump Mounting Kit

Facet Fuel Pump Mounting Kit.

Antivibration mounts + earthing wire for Facet Cube, GOLD-FLO and Interrupter series fuel pumps.

Facet Fuel Pump Mounting Kit

FPA906

1/8'' Screw-On Fuel Pump Filter

This is a special screw-on fuel filter to be used with a variety of electric fuel pumps.

Failure to operate those pumps with a suitable filter like this usually voids the warranty on the pump!

This filter suits, amongst others, the Airtex 6Volt filter and the range of Solid State fuel filters by Facet.

Couplings Specifications:
Connection to pump body: 1/8" NPTF tapered thread
Fuel Union for fuel lines with 8 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

1/8'' Screw-On Fuel Pump Filter

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

WC99902.057
Inertia Fuel Cut-Off Switch

Inertia Fuel Cut-Off Switch

Webcon electric fuel pump cut-off safety switch.

This inertia switch detects the rapid change in velocity of a vehicle when impacted in any direction and is designed to be wired into the supply of the fuel pump to cut the power to the pump in the event of an accident.

The switch is normally immune to normal road vibration and road irregularities.

Suitable for under-bonnet fitment providing the switch is free from the risk of spillage of liquids or direct water spray.

The installation manual (in English) can be downloaded HERE.

Please note that this is the inertia switch ONLY. In order to wire this switch into you vehicle, you need a connector set which can be purchased separately or ordered right along with the switch by selecting it through the drop box at the top of this description.

Inertia Fuel Cut-Off Switch

WC99902.083
Connector Set for Inertia Fuel Cut-Off Switch

Connector Set for Inertia Fuel Cut-Off Switch

Connector set for our Webcon Inertia Fuel Cut-Off Switch.

This set is required when you wire our Inertia Switch into your vehicle for the first time.

The installation manual (in English) for the Inertia Switch can be downloaded HERE.

 

 

 

Connector Set for Inertia Fuel Cut-Off Switch