10 MM Fuel Lines
10 MM Fuel Lines

10 MM Fuel Lines

On this page you will find fuel lines, fuel unions and related materials with 10 mm diameter.

This means that the outlet has an external diameter of 10 millimeter, suitable for fuel line with an internal diameter of that same 10 millimeter.

The inlet diameter and thread varies. Please see the individual item description for details.

10 MM Fuel Lines

!
2134.0800
Cohline E10-resistant fuel line hose with 10 mm inner diameter

Cohline E10-resistant fuel line hose with 10 mm inner diameter

This is the top-of-the-line Cohline, E10-resistant, flexible fuel line / hose.

This fuel hose has an 9.5 mm inner diameter and 15.5 mm outer diameter, suitable for fuel unions of 10 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 70 mm

This hose uses 14 - 16 mm jubilee clips.

Cohline E10-resistant fuel line hose with 10 mm inner diameter

2134.01.0800
Cohline E10-resistant fuel line hose with 10 mm inner diameter and steel braiding

Cohline E10-resistant fuel line hose with 10 mm inner diameter and steel braiding

This is the top-of-the-line Cohline, steel-braided E10-resistant, flexible fuel line / hose.

This fuel hose has an 9.5 mm inner diameter and 17.5 mm outer diameter, suitable for fuel unions of 10 mm outer diameter.

It is sold in lengths of 1 meter (3 Feet 3 3/8 inch).

When ordering multiple lengths, we will do our best to supply it as 1 piece.

Maximum, single, length: 15 meters.

Black rubber textile reinforced hose for conveying commercial fuels, including Super Grade and E10.
Also suitable for Diesel fuels with Bio–Diesel addition.

Construction:

  • Cover: Black smooth CR
  • Reinforcement: High tensile synthetic textile plies
  • Liner: Black smooth NBR

Temperature:

  • -30°C to + 50°C (Petrol), 65°C (Diesel) / -22°F to + 122°C (Petrol), 149°C (Diesel)

Safety Factor:

  • 3:1 (Burst pressure = 3 x working pressure)

Regular pressures:

  • Regular working pressure: 10 Bars / 145 PSI
  • Tested pressure: 20 Bars / 290 PSI
  • Bursting pressure: 30 Bars / 435 PSI

Minimum bend radius in mm:

  • 80 mm

Cohline E10-resistant fuel line hose with 10 mm inner diameter and steel braiding

FPA904/B
10 mm Pipe Union with 1/4 NPTF thread

10 mm Pipe Union with 1/4 NPTF thread

Brass straight 10 mm Pipe Union with 1/4th thread.

Union with 1/4" NPTF tapered thread for fuel lines with an internal diameter of 10 mm.

Specification:
Inlet: 1/4" tapered NPTF
Outlet: 10 millimeter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

Despite the barbed edge on these unions, we strongly advise you to secure your fuel lines using our Premium Quality Stainless Steel Jubilee Clips.

For your convenience, you can order these right along with the joiner by simply selecting them through the dropbox.

10 mm Pipe Union with 1/4 NPTF thread

FPA903/C
10 mm Pipe Union with 1/8 NPTF thread

10 mm Pipe Union with 1/8 NPTF thread

Straight 10 mm Pipe Union with 1/8th thread.

Union with 1/8" NPTF tapered thread for fuel lines with an internal diameter of 10 mm.

Specification:
Inlet: 1/8" tapered NPTF
Outlet: 10 millimeter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips.
For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

10 mm Pipe Union with 1/8 NPTF thread

J808
Fuel Line Joiner 10 mm - 10 mm

Fuel Line Joiner 10 mm - 10 mm

Fuel Line Joiner 10 mm - 10 mm.

This is a coupling to connect two pieces of flexible fuel line.

This concerns fuel line with an internal diameter of 10 mm.

Overall length: 49 mm

Adds a mere 9 mm to the length of your fuel line.

Despite the barbed ends, we do advise you to use our premium quality jubilee clips to secure your fuel line onto this joiner.

For your convenience, you can order these right along with the joiner by simply selecting them through the dropbox.

Alternatively, you can go HERE for our accessories for 10 mm fuel line.

Fuel Line Joiner 10 mm - 10 mm

J806
Fuel Line Adapter 8 mm - 10 mm

Fuel Line Adapter 8 mm - 10 mm

Metal Fuel Line Adapter 8 mm - 10 mm.

This is coupling to connect two pieces of flexible fuel line.

This concerns one fuel line with an internal diameter of 8 mm and one with an internal diameter of 10 mm.

Overall length: 50 mm

Adds a mere 9 mm to the length of your fuel line.

Despite the barbed ends, we do advise you to use our premium quality jubilee clips to secure your fuel line onto this joiner.

For your convenience, you can order these right along with the joiner by simply selecting them through the dropbox.

Alternatively, you can go HERE for our accessories for 10 mm fuel line or HERE for our accessories for 8 mm fuel line.

Fuel Line Adapter 8 mm - 10 mm

T10
10 mm Fuel T-Piece

10 mm Fuel T-Piece

Brass Fuel T-Piece for fuel lines with an internal diameter of 10 millimeter.

We strongly advise you to secure your fuel lines using our stainless steel jubilee clips, despite the barbed edge on these unions.

For your convenience, you can order these clips right along with the union by simply selecting it through the drop-box above.

 

10 mm Fuel T-Piece

FPA9022/B x 0.5
Sytec 10 mm Pipe Union 90 Degrees with 1/4 NPTF thread

Sytec 10 mm Pipe Union 90 Degrees with 1/4 NPTF thread

Sytec 10 mm Pipe Union 90 Degrees with 1/4 thread for, amongst others, Facet Red Top Fuel Pump.

Union with 1/4" NPTF tapered thread for fuel lines with an internal diameter of 10 mm.

Specification:
Inlet: 1/4" tapered NPTF
Outlet: 10 millimeter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.
As an alternative, you can use our Loctite 243 Thread Locker which will offer the added properties of protecting your connections from undoing themselves.

Sytec 10 mm Pipe Union 90 Degrees with 1/4 NPTF thread

norm5mm
Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide

Endless Band Hose Clamp with Buckle - 5 mm wide.

Again one of those items that allows you to put the finishing touches on a restoration!

This is the famous "endless band hose clamp with buckle" that was used throughout the 1950's, 1960's and 1970's in the car industry.

Unfortunately, these band clamps are only suitable for one-time use and are discarded after removing them.

Over the years, these clamps have become harder and harder to find but we managed to find a source!

We are selling these in sets.

Such a set consist of the following:

  • Approximately 100 cm Zinc-plated band, 5 millimeters wide
  • 3 buckles

This way, you have roughly a foot (or 33 cm) of band per clamp / buckle which is more than enough for regular applications.

Thanks to the generous length of band, there is virtually no limit to the diameter or circumference of the clamp that you wish to apply although these were usually applied to small diameter fuel lines.

Please note that this style of clamping is NOT suitable for steel-braided lines.

Endless Band Hose Clamp with Buckle - 5 mm wide

jubilee14-16
14 - 16 mm Stainless Steel Jubilee Clip Hose Clamp

14 - 16 mm Stainless Steel Jubilee Clip Hose Clamp

Stainless Steel Jubilee Clip Hose Clamp 14 - 16 mm for 10 mm Flexible Fuel Line.

Neatly finished, this stainless steel (Grade 304) hose clamp (or jubilee clip if you want) is the perfect compliment to your fuel hose.

It is rated for between 14 and 16 mm external hose diameter with 10 mm internal diameter.

Can be tightened using a 7 mm socket or flat head screwdriver.
Excellently suited for use with our Gates Flexi Driver tool.

14 - 16 mm Stainless Steel Jubilee Clip Hose Clamp

CARTERW4259
Carter 6 Volt Low-Pressure Fuel Pump - Dual Polarity

Carter 6 Volt Low-Pressure Fuel Pump - Dual Polarity

This is a special fuel pump for vehicles with a 6 Volt electrical system.

What makes this pump extra special is the fact that it is a Dual-Polarity pump. In other words: it is both suitable for vehicles with a Negative Earth as well as vehicles with a Positive Earth.

Despite being a 6 Volt pump, the output is an incredible 72 Gallons per Hour or 270 Liters!

Thanks to its low output pressure of 5.75 PSI / 0.4 Bar, it usually does not require a pressure regulator but please check your system requirements to make sure.

In case you still need to reduce the pressure, our Pressure Regulators can be found HERE.

Pump specification:

  • Flow rate: 72 Gallons/hour - 270 liters/hour
  • Pressure: 5.75 PSI / 0.4 Bar
  • Pipe union thread size: 1/4" NPT tapered thread
  • Power supply: 6 Volt Negative Earth AND 6 Volt Positive Earth
  • Suitable for nearly all fuels, including modern ones, but NOT suited for Methanol or Diesel

The kit includes:

  • Pump
  • Mounting bracket and materials
  • 10 mm inlet and outlet unions with spring-type hose clips

Couplings Specifications:
Connection to pump body: 1/4" NPT tapered thread
Fuel Unions for fuel lines with 10 mm internal diameter

Please use our superior quality PTFE tape each time that you (re-)assemble screwed connections in the fuel tract in order to properly seal the connection.

As an alternative, you can use our Loctite 542 Thread Sealant which will offer the added properties of protecting your connections from undoing themselves.

We strongly advise you to secure your fuel lines using our Stainless Steel Jubilee Clips.

Carter 6 Volt Low-Pressure Fuel Pump - Dual Polarity

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker

67263TS
Roll of Superior Quality PTFE Thread Sealing Tape

Roll of Superior Quality PTFE Thread Sealing Tape

Roll of superior quality PTFE tape, used to thoroughly seal the connection of screw-in couplings on the bodies of fuel pumps, pressure regulators, fuel filters and the likes.

12 millimeter wide

Roll of 12 meters (around 36 ft. !); probably enough to last you a life-time!

As an alternative, you can use our Loctite 243 Thread Locker which will offer the added avantage of securing the connection.

 

 

Roll of Superior Quality PTFE Thread Sealing Tape

FLEXIDRIVER
Flexi Driver tool to tighten Jubilee Clips

Flexi Driver tool to tighten Jubilee Clips

Special flexible tool to correctly tighten jubilee clips.

This Flexidriver is a highly effective, torque sensitive screwdriver, calibrated to bend when the proper torque is attained.

Apart from that, it's a handy tool with flexible shaft to tighten the clamps properly, also in hard-to-reach places.

Suitable for 7 mm connectors.

Flexi Driver tool to tighten Jubilee Clips